ANALISA SIFAT MEKANIK PENGARUH VARIASI PERENDAMAN DAN PENEKANAN PADA KOMPOSIT BERBAHAN SERAT BUNDUNG
DOI:
https://doi.org/10.26418/elkha.v12i2.40917Keywords:
composites, resins, bundle fibers, mechanical properties.Abstract
This study aims to determine the effect of mechanical properties of impact, bending and tensile of bundle fiber composites with 5% NaOH variation of immersion time 0.5 hours, 1 hour and 1.5 hours. Then the blending and casting process is carried out to form a composite material with 20% fiber and 80% resin binder with a catalyst content of 1% and pressurized with press variations of 5 kg, 10 kg and 15 kg. The results of the blending and casting process are made according to the testing standard and then testing the mechanical properties. Impact, bending and tensile strength test results showed that immersion of 0.5 hours with 15 Kg concentration produced the highest value, namely Impact strength 94.89 J / mm2, bending strength 17.77 N / mm2 and tensile strength 27 N / mm2. Whereas the fracture form of the composite is the binding and fiber breaking evenly at the same point and the fiber is not pulled from the metric.References
Mohit Sood, Gaurav Dwivedi (2017), Effect of fiber treatment on flexural properties of natural fiber reinforced composites, Egyptian Journal of Petroleum xxx (2017).
Emad Omrani, Pradeep L. Menezes b, Pradeep K (2016), Rohatgi State of the art on tribological behavior of polymer matrix composites reinforced with natural ï¬bers in the green materials world, Engineering Science and Technology, an International Journal 19 (2016) 717–736.
Onkar V. Potadara, Ganesh S. Kadama (2018), Preparation and Testing of Composites using Waste Groundnut Shells and Coir Fibres, Procedia Manufacturing 20 (2018) 91–96.
Sitohang, N. 2015. Studi Pemanfaatan Rumput Bundung (Scirpus Grossus Linne) Sebagai Serat Alami Bahan Alat Penangkapan Ikan Dengan Pengujian Kekuatan Putus (Breaking Strength) Dan Kemuluran (Elongation). Fakultas Perikanan Dan Ilmu Kelautan . Universitas Riau. Pekanbaru. 70 hal. (Tidak diterbitkan)
ASTM D 256, Standart Test Methde for determining charpy impact sffength af Plastic. American Sosiety for Testing Materials, Philadelphi4 PA.
ASTM. D 790 – 02, Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating material. Philadelphia, PA : American Society for Testing and Materials.
ASTM International, The Composite Materials Handbook, Polymers Matrix Composite, volume 3. Baltimore, USA.
R. Pragatheeswaran, S. Senthil Kumaran (2015), Mechanical behaviour of groundnut shell powder/calcium carbonate/vinyl ester composite, International Journal of Current Engineering and Scientific Research, 2 (2015) 28-31.
A. Atiqah, M. jawaid, M.R. Ishak, S.M. Sapuan (2017), Moisture Absorption and Thickness Swelling Behaviour of Sugar Palm Fibre Reinforced Thermoplastic Polyurethane, Procedia Engineering 184 ( 2017 ) 581-586.
Onkar V. Potadar, Akshay A. Pashilkar, Anson Z. Abraham, Dipak S. Chavan, Meljo Saji, Preparation and testing of composite materials (2016), Unpublished Thesis–SIES GST, Nerul, Navi Mumbai, M.S., India, 2016.
D. Tchepel, F.A.O. Fernandes, O. Anjos, R.J. Alves de Sousa (2016). Mechanical properties of natural cellular materials. In: Reference Modules in Materials Science and Materials Engineering, Elsevier, 2016.
William D. Callister, Jr., David G. Rethwisch (2014), Materials Science and Engineering, Wiley USA, 2014.
Krishan K. Chawla (2013), Composite Materials, Springer New York, 2013.
Downloads
Additional Files
Published
Issue
Section
License
Copyright (c) 2020 ELKHA : Jurnal Teknik Elektro
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
1. Proposed Policy for Journals That Offer Open Access
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
2. Proposed Policy for Journals That Offer Delayed Open Access
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication, with the work [SPECIFY PERIOD OF TIME] after publication simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
