Analisa Unjuk Kerja Tanur Listrik Mengunakan Kawat Kanthal A1 Diameter 1 Milimeter
Keywords:
electric furnace, kanthal A1, performanceAbstract
Kanthal A1 wire components have been used in electric furnaces in basic mechanical engineering laboratories, but until now the performance of electric furnaces has not been measured based on the use of A1 kanthal wire diameters. In this study, an analysis of the performance of the electric furnace was carried out on the diameter of the A1 kanthal wire using a diameter of 1 mm. In addition, an analysis was also carried out by comparing the energy consumption of the electric furnace against the diameter of the A1 kanthal wire. Based on the results of the tests and analysis carried out, the results obtained were the use of A1 kanthal wire with Ø 1 mm having a total of 799 turns. Based on the use of a temperature measuring instrument, it is known that the maximum temperature that can be achieved by an electric furnace is 700 ºC, while the average temperature increase rate is the average is 0.061 ºC. The consumption of electric heating wire ∅ 1 mm to reach a temperature of 700 ºC takes 50 minutes, while the required power is 2,404.6 watts.
References
M. F. Hasanuddin et al., “Analisa Perpindahan Panas Furnace Menggunakan Kawat Nikelin 2 mm,†pp. 275–280, 2022.
M. R. Rahmat, “Perancangan Dan Pembuatan Tungku Heat Treatment,†2015. [Online]. Available: http://ejournal.unismabekasi.ac.id/
H. Lubis and A. F. Abas, “Rancang bangun alat penggongseng kelapa untuk pembuatan bumbu dapur dengan menggunakan pemanas listrik temperatur 800c dengan kapasitas 3 kg,†J. POLIMESIN, vol. 14, no. 1, p. 21, 2016, doi: 10.30811/jpl.v14i1.297.
D. Purwanto and R. A. Nasa, “Perancangan Tungku Pemanas Dengan Menggunakan Kanthal a1,†Media Mesin Maj. Tek. Mesin, vol. 22, no. 1, pp. 13–21, 2021, doi: 10.23917/mesin.v22i1.12462.
V. Veinard Vingtsabta, A. Syakur, and A. Warsito, “Analisis Dan Perbandingan Jenis Kawat Kanthal A-1 Dan Nichrome 80 Sebagai Elemen Pemanas Pada Oven Listrik Hemat Energi.â€
F. T. Industri, “Analisis Kinerja Dan Efisiensi Continuous Furnace Untuk Aplikasi Produksi,†2019.
P. Studi, P. Fisika, and U. Muhammadiyah, “Analisis resistansi coil kawat tembaga terhadap perubahan suhu sangat rendah sebagai rancang dasar pengukuran suhu rendah,†pp. 73–83.
A. D. Saputri, “Jenis Kawat Penghantar Berdasarkan Deret Volta Menggunakan Kalorimeter,†Digit. Repos. Univ. Jember, pp. 1–43, 2017.
S. Pendidikan, P. Studi, P. Teknik, and M. K. Faza, “Pengaruh variasi jumlah lilitan coil induktansi tehadap perubahan temperatur pada dapur induksielektromagnetik,â€2020,.Available:http://lib.unnes.ac.id/42760/1/5201415046.pdf
Z. Arif, Nazarudin, and T. Kamaruzzaman, “Simulasi Distribusi Aliran Temperatur Pada Lapisan Dinding Tungku ( Furnace ) Dengan Menggunakan Program Ansys 5,4,†J. Ilm. JURUTERA, vol. 02, no. 01, pp. 096–101, 2015.
Kanthal, “Heating Alloys for Electric Household Appliances,†Kanthal Handb.,p.100,2003,[Online].Available:http://www.westl.com/uploads/tdpdf/06080303.pdf
P. N. Lhokseumawe, K. Pengantar, rahayu deny danar dan alvi furwanti Alwie, A. B. Prasetio, and R. Andespa, “Tugas Akhir Tugas Akhir,†J. Ekon. Vol. 18, Nomor 1 Maret201, vol. 2, no. 1, pp. 41–49, 2020.
F. Savira and Y. Suharsono, “Element Pemanas,†J. Chem. Inf. Model., vol. 01, no. 01, pp. 1689–1699, 2013.
K. K. Furnace, “Sistem Otomasi Mikrocontroler Untuk Furnace dengan Kapasitas 7000 Watt,†pp. 1–6, 2020.
